Om alle functies van onze shop te kunnen gebruiken, adviseren wij u om Javascript in uw browser in te schakelen.

4730-186 Führungsblech für Arretierstange P/N=30200

Hafenarretierung Ersatzteile

Hafenarretierung Ersatzteile

4730-186 Führungsblech für Arretierstange P/N=30200

Hafenarretierung Ersatzteile

Hafenarretierung Ersatzteile

ENO/FORCE 10 Führungsblech für Arretierstange P/N=30200

Artikelnummer: 4730-186

ENO-nr. 30200

ENO/FORCE 10 Geleideplaat voor vergrendelingsstang van het gimbal slot.
Er zijn 3 geleideplaten nodig voor de cardanische vergrendeling.

Geschikt voor alle FORCE 10 ovens met cardanische ophanging.

€ 8,50*

netto: € 7,14

Prijzen incl. BTW en excl. verzendkosten

Voorraad

Stk

Beschrijving

ENO-nr. 30200

ENO/FORCE 10 Geleideplaat voor vergrendelingsstang van het gimbal slot.
Er zijn 3 geleideplaten nodig voor de cardanische vergrendeling.

Geschikt voor alle FORCE 10 ovens met cardanische ophanging.

Vragen over het artikel?

Vragen over het artikel?

Praat met vakmensen, botenbouwers en zeilers. Wij begrijpen uw vragen en geven u het juiste antwoord.

Neem contact op met experts

Meer artikelen uit de categorie Reserveonderdelen voor gaskooktoestellen en fornuizen

ENO / FORCE 10 - Branderkap klein

ENO / FORCE 10 - Burner cap small

ENO No. 60031 Burner cap for small burners, outer diameter 50 mm. Top part of the SABAF 3 burners.The cap is positioned above the flame distributor and is locked in place by a rotating movement on two pins protruding from the stove surface. This fixation ensures that both the flame distributor and the burner cap remain attached to the burner and cannot come loose due to vibrations.

€ 18,90 *

4730-110 ENO/FORCE 10 Drehknopf für Gasbrenner P/N F89248 - Bild 1

ENO / FORCE 10 - draaiknop voor gasbrander

ENO Nr. F89248 Gasbrenner Einstellknopf für FORCE 10 Herde. 3-Teilig, bestehend aus Grundplatte, Edelstahlfeder und Drehknopf. Außendurchmesser der Grundplatte 46 mm.

€ 23,90 *

ENO / FORCE 10 - Elektronische ontstekingsmodule, 6 aansluit

ENO / FORCE 10 - Electronic ignition box, 6 connections

ENO No. 72655 Electronic ignition box with 6 connections.The ENO / FORCE 10 high-voltage part for electric ignition is an original spare part for marine stoves and stoves. It reliably generates the necessary ignition spark and ensures the safe start-up of gas hobs on board. The compact design facilitates installation in existing ENO / FORCE 10 cooking systems.The robust construction is specially designed for use in a maritime environment and withstands the typical stresses at sea. Replacing this high-voltage part restores the full functionality of the ignition system and ensures the operational safety of your cooking appliances.

€ 72,90 *

ENO / FORCE 10 - grote branderdop

ENO / FORCE 10 - Large burner cap

ENO No. 60026 Burner cap for large burners, outer diameter 95 mm. Top part of the SABAF 3 burners.The cap is positioned above the flame distributor and is locked in place by a rotating movement on two pins protruding from the stove surface. This fixation ensures that both the flame distributor and the burner cap remain attached to the burner and cannot come loose due to vibrations.

€ 21,90 *

ENO / FORCE 10 - Handknop voor panhouder

ENO / FORCE 10 Hand knob for pot holder

ENO No. 55036 This black locking knob is suitable for ENO / FORCE 10 pot holders.The knob has a diameter of 34 mm and has an integrated 4 mm threaded screw.The pot holder is fixed by screwing the handwheel into the pot frame and can be moved back and forth by loosening it.

€ 21,90 *

4730-120 ENO/FORCE 10 Brenner Unterteil klein P/N 60028 - Bild 1

ENO / FORCE 10 - klein onderstuk voor brander

ENO Nr. 60028 Unterteil des kleinen SABAF 3 Brenners, der ab 2012 in den FORCE 10 Herden verbaut wird.Die Oberteile – Brennerkappe und Flammenverteiler – werden an den aus der Herdfläche ragenden Stiften des Unterteils fixiert. Dadurch lösen sich die Teile selbst bei Bewegungen und Erschütterungen des Schiffes nicht.

€ 34,90 *

ENO / FORCE 10 - kleine vlamverdeler

ENO / FORCE 10 - Small Flame Spreader

ENO No. 60029 Flame distributor made of aluminum for small SABAF 3 burners, which will be installed in FORCE 10 stoves from 2012.The burner cap is locked in place by a rotating movement on two pins protruding from the stove surface and thus fixes both itself and the flame distributor to the burner. This means that the parts do not come loose even if the boat moves or is shaken.

€ 29,50 *

4730-118 ENO/FORCE 10 Brenner Unterteil groß P/N 60024 - Bild 1

ENO / FORCE 10 - onderstuk brander / groot, voor bovenbrande

ENO Nr. 60024 Unterteil des großen SABAF 3 Brenners, der ab 2012 in den FORCE 10 Herden verbaut wird.Die Unterteile werden ohne Düse geliefert.Die Oberteile – Brennerkappe und Flammenverteiler – werden an den aus der Herdfläche ragenden Stiften des Unterteils fixiert. Dadurch lösen sich die Teile selbst bei Bewegungen und Erschütterungen des Schiffes nicht.

€ 42,90 *

4730-103 ENO/FORCE 10 Topfhalter links, Länge 227 mm P/N 63622 - Bild 1

ENO / FORCE 10 - Pot holder left, length 227 mm

ENO No. 63622 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

€ 21,90 *

ENO / FORCE 10 - panhouder rechts, lengte 227 mm

ENO / FORCE 10 - Pot holder right, length 227 mm

ENO No. 63623 Pot holder right, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

€ 21,90 *

ENO / FORCE 10 - Panhouder rechts, lengte 272 mm

ENO / FORCE 10 - Pot holder right, length 272 mm

ENO No. 63625 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

€ 21,90 *

ENO / FORCE 10 - Pannendrager links, lengte 272 mm

ENO / FORCE 10 - Pot holder left, length 272 mm

ENO No. 63624 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various current FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the locking knob and can be moved back and forth as required by loosening it.Supplied without locking knob.

€ 21,90 *

4730-183 Gummikappe für Feststellhebel P/N=71268

ENO / FORCE 10 - Rubberen kap voor vergrendelingshendel

ENO-nr. 71268ENO/FORCE 10 rubberen dop voor vergrendelingshendel van het gimbal slot.Geschikt voor alle FORCE 10 fornuizen met cardanische bevestiging.

€ 4,50 *

ENO / FORCE 10 - temperatuursensor bouwjaar 2000 - 2012

ENO / FORCE 10 - Thermocouple year 2000 - year 2012

ENO No. F89216 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

€ 25,89 *

ENO / FORCE 10 - Temperatuursensor bouwjaar 2012 - 2020

ENO / FORCE 10 - Thermal sensor year 2012 - year 2020

ENO No. 60032 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

€ 21,90 *

ENO / FORCE 10 - Temperatuursensor vanaf bouwjaar 2020

ENO / FORCE 10 - Thermocouple from 2020 onwards

ENO No. 71673 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

€ 26,91 *

ENO / FORCE 10 - Thermostatisch gasventiel, oven+grill

ENO / FORCE 10 - Thermostatic gas valve, oven+grill

ENO No. 72137 Thermostatic gas valve for supplying gas to the oven and grill burner.This high-quality valve is a further development of the old model and improves performance and efficiency.It replaces the old model ENO No. 89214

€ 139,00 *

4730-182 Feder für Arretierstange P/N=63628

ENO / FORCE 10 - Veer voor sluitstang

ENO Nr. 63628Veer voor de sluitstang. Er zijn 2 veren nodig voor elke havensluis.Geschikt voor alle FORCE 10 kooktoestellen met cardanische ophanging.Lengte 70 mmDiameter 8 mm

€ 3,50 *

ENO / FORCE 10 - vlamverdeler voor grote topbrander

ENO / FORCE 10 - vlamverdeler voor grote topbrander

ENO Nr. 60025 Flammenverteiler aus Aluminium für große SABAF 3 Brenner, die ab 2012 in den FORCE 10 Herden verbaut werden.Die Brennerkappe wird durch eine Drehbewegung auf zwei aus der Herdoberfläche ragenden Stiften arretiert und fixiert damit sowohl sich selbst als auch den Flammenverteiler am Brenner. Dadurch lösen sich die Teile selbst bei Bewegungen und Erschütterungen des Schiffes nicht.

€ 37,50 *

4721-131 ENO/FORCE 10 Batteriehalter für elektr. Zündung P/N 72647 - Bild 1

ENO / FORCE 10 battery holder for electric ignition

ENO No. 72647 Battery holder for holding an AA 1.5 volt battery to supply the ignition box of the ENO / FORCE 10 gas stoves with power and thus reliably and conveniently ignite the individual gas burners.

€ 27,91 *

ENO/FORCE 10 - Elektronische ontstekingsbox 4 aansluitingen

ENO/FORCE 10 - Electronic ignition box 4 connections

ENO No. 72645 Electronic ignition box with 4 connections.The ENO / FORCE 10 high-voltage ignition part is a genuine spare component for marine stoves and cookers. It reliably generates the required ignition spark, ensuring safe operation of your onboard gas cooking systems. Its compact design allows for easy integration into existing ENO / FORCE 10 appliances.Built with a durable construction, it is specifically designed to withstand the demanding conditions at sea. Replacing this part restores full functionality of the ignition system and ensures the operational safety of your cooking equipment.

€ 69,00 *

Laatst bekeken producten

Verzoek succesvol verzonden

de offerte kon niet worden verzonden omdat er een probleem is opgetreden. Alstublieft opnieuw proberen.