ENO / FORCE 10 - Electronic ignition box, 6 connections

ENO No. 60031 Burner cap for small burners, outer diameter 50 mm. Top part of the SABAF 3 burners.The cap is positioned above the flame distributor and is locked in place by a rotating movement on two pins protruding from the stove surface. This fixation ensures that both the flame distributor and the burner cap remain attached to the burner and cannot come loose due to vibrations.

ENO No. F89248 Gas burner control knob for FORCE 10 stoves. 3-part, consisting of base plate, stainless steel spring and rotary knob. Outer diameter of the base plate 46 mm.

ENO No. 60026 Burner cap for large burners, outer diameter 95 mm. Top part of the SABAF 3 burners.The cap is positioned above the flame distributor and is locked in place by a rotating movement on two pins protruding from the stove surface. This fixation ensures that both the flame distributor and the burner cap remain attached to the burner and cannot come loose due to vibrations.

ENO No. 55036 This black locking knob is suitable for ENO / FORCE 10 pot holders.The knob has a diameter of 34 mm and has an integrated 4 mm threaded screw.The pot holder is fixed by screwing the handwheel into the pot frame and can be moved back and forth by loosening it.

ENO Nr. 60028 Unterteil des kleinen SABAF 3 Brenners, der ab 2012 in den FORCE 10 Herden verbaut wird.Die Oberteile – Brennerkappe und Flammenverteiler – werden an den aus der Herdfläche ragenden Stiften des Unterteils fixiert. Dadurch lösen sich die Teile selbst bei Bewegungen und Erschütterungen des Schiffes nicht.

ENO No. 60029 Flame distributor made of aluminum for small SABAF 3 burners, which will be installed in FORCE 10 stoves from 2012.The burner cap is locked in place by a rotating movement on two pins protruding from the stove surface and thus fixes both itself and the flame distributor to the burner. This means that the parts do not come loose even if the boat moves or is shaken.

ENO Nr. 60024 Unterteil des großen SABAF 3 Brenners, der ab 2012 in den FORCE 10 Herden verbaut wird.Die Unterteile werden ohne Düse geliefert.Die Oberteile – Brennerkappe und Flammenverteiler – werden an den aus der Herdfläche ragenden Stiften des Unterteils fixiert. Dadurch lösen sich die Teile selbst bei Bewegungen und Erschütterungen des Schiffes nicht.

ENO No. 63622 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63623 Pot holder right, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63625 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63624 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various current FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the locking knob and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. F89216 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

ENO No. 60032 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

ENO No. 71673 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

ENO No. 72137 Thermostatic gas valve for supplying gas to the oven and grill burner.This high-quality valve is a further development of the old model and improves performance and efficiency.It replaces the old model ENO No. 89214

ENO No. 60025 Flame spreader made of aluminum for large SABAF 3 burners, which will be installed in FORCE 10 stoves from 2012.The burner cap is locked in place by a rotating movement on two pins protruding from the stove surface, thus fixing both itself and the flame distributor to the burner. This means that the parts do not come loose even if the boat moves or is shaken.

ENO No. 72647 Battery holder for holding an AA 1.5 volt battery to supply the ignition box of the ENO / FORCE 10 gas stoves with power and thus reliably and conveniently ignite the individual gas burners.

ENO No. 72645 Electronic ignition box with 4 connections.The ENO / FORCE 10 high-voltage ignition part is a genuine spare component for marine stoves and cookers. It reliably generates the required ignition spark, ensuring safe operation of your onboard gas cooking systems. Its compact design allows for easy integration into existing ENO / FORCE 10 appliances.Built with a durable construction, it is specifically designed to withstand the demanding conditions at sea. Replacing this part restores full functionality of the ignition system and ensures the operational safety of your cooking equipment.